Perth and Kinross · Scotland
Fire-rated sealant in Markethill, Perth and Kinross
Problem with your fire-stopping gaps in Markethill? We cut out the old, prepare the joints and apply the right sealant, with a one-year guarantee.
- Seals cut through by electricians, plumbers or data installers
- Open gaps behind door architraves
- New service routes left unsealed after building work
Fire rated sealant in Markethill
Later work by other trades often breaks through fire stopping, especially in flats, HMOs, offices and schools. One new cable or pipe can leave a gap that nobody goes back to seal. Those are the gaps we close, using a tested fire-rated product. We work on pipe & cable gaps, linear gaps and door frames, and people most often call us about gaps filled with a product that isn’t fire-rated and cracked or shrunken fire-rated sealant.
Commercial work around smaller Scottish places tends to mean hotels, guest houses, schools and halls rather than offices. All of them have washrooms, kitchens and fire-rated joints that need looking after.
We stand behind the work with a one-year guarantee.
- Where
- Markethill (PH13)
- Region
- Perth and Kinross
- Cover
- 12 months on all our work
- Quote
- Quoted before any work starts
- info@mrmastic.co.uk
- Page updated
- 26 October 2026
Common problems we fix in Markethill
In some buildings the gap was filled with the wrong thing in the first place: general-purpose foam, everyday silicone or caulk where a fire-rated seal was needed. It may look fine, but it isn’t a fire-rated seal.
Keep an eye out for any of the following:
- Joints picked up in a fire-stopping survey
- Fire seals that have cracked with movement
- Seals cut through by electricians, plumbers or data installers
- Open gaps behind door architraves
For buildings such as Abbey Church, older buildings that have had new heating or wiring often have service gaps worth checking.
What your quote should include
- Whether the sealant suits the joint
- What insurance they hold
- How the colour is chosen
- How the joint is cleaned and prepared
How to look after the new joints
Aftercare is simple:
- Include fire stopping when you schedule refits
- Ask which product was used before you paint
- Keep the record of products and locations with your fire safety documents
- Get damaged fire seals looked at promptly
Do not add foam, filler or ordinary sealant over a fire seal. If it needs repair, use the same type of product. We can tell you which product we used.
Any job that breaks through a wall or ceiling should include resealing. Doing it at the time avoids leaving gaps behind.
How we quote for fire rated sealant
Every job gets its own quote. This is what makes a difference:
- Whether the work is at height
- Working hours on commercial sites
- How many rooms, windows or areas are involved
- Any mould that needs treating
Every job is a little different, so we quote each one individually. Size, access and the product the joint needs all make a difference.
What to tell us for a quote
To make quoting easier, let us know:
- Roughly how big the job is
- The address or postcode of the job
- The problem you’ve noticed
- How we’d reach the joints
To get a quote, drop us a line at info@mrmastic.co.uk and tell us where the job is and what the problem looks like. We’ll send you a clear quote before any work starts.
The process
On the day, we start by going over the job with you, so there are no surprises. Surfaces next to the work are protected before any work begins. The work usually takes a few hours for a handful of gaps, and longer for a whole building. In smaller Scottish places, parking is normally less of an issue than access and distance. Tell us how to find the property and how to reach the work.
- Before starting, we go through the specification or action list with you.
- Each gap is measured and its substrate and service noted.
- Any non-fire-rated filler is removed.
- The specified fire-rated sealant goes in over any backing its detail requires.
- We hand over a list of locations and products for your records.
Preparing for the visit
- Tell us about access, such as stairs, a lift or high-level joints
- Clear the area around the work
- Tell us about any water getting in
How to get a quote
For fire rated sealant in Markethill, drop us a line at info@mrmastic.co.uk. Tell us what the problem is and where, and we’ll agree the price before any work begins.
Related advice
Can I do it myself?
If you do try it yourself, take your time over the preparation: take out all the old sealant, make sure the joint is clean and dry, and give it the full cure time. If it fails, we can still redo it.
Not every job suits DIY: work at height, external movement joints, fire-rated sealant and large areas call for the right materials, safe access and experience.
Towns and villages near Markethill
More services for Markethill
Commercial buildings in Markethill
There are hotels and other places to stay in and around Markethill. Hotel work can be planned room by room, with out-of-hours working where needed. In Scotland, building work comes under the Building (Scotland) Regulations and their technical handbooks. We install fire-rated sealant to the product’s tested details; we do not certify buildings or carry out fire risk assessments.
In and around Markethill, as anywhere, good fire rated sealant starts with a clean, dry, properly prepared joint.
Markethill is about 5 miles south-east of Blairgowrie and Rattray, in Perth and Kinross. Wherever you are in the PH13 postcode area, we can carry out fire rated sealant at your property. 107 places in Perth and Kinross are on our list, large and small. You can also see our page for Dundee, roughly 12 miles from Markethill.
Postcode districts we cover here for fire rated sealant: PH13. Neighbouring places we cover for fire rated sealant include Coupar Angus (1 mile north-west), Woodside (2 miles south-west), Burrelton (2 miles south-west), Ardler (3 miles north-east) and Carsie (4 miles north-west). Further out, we also cover Perth (12 miles south-west), Blairgowrie and Rattray (5 miles north-west), Letham (13 miles south-west), Scone (10 miles south-west), Tulloch (12 miles south-west) and Alyth (6 miles north).
Landmarks near Markethill
Other landmarks nearby include Kinclaven Castle (4.4 miles west) and Blairgowrie Community Hospital (4.6 miles north-west). The countryside around Markethill includes Northballo Hill and Monk Myre.
Why deal with it now?
Paying for fire stopping that has to be redone is a false economy. Work that doesn’t follow the tested detail may have to come out again when the building is next checked. In an older home around Markethill, damp from a failed joint can get into timber and plaster, which is a far bigger job than the sealant.
Combining jobs into one visit generally makes better use of the time than several visits. You will get one clear quote for the whole job.
Why choose Mr Mastic in Markethill
- Fully insured
- Experience in homes, commercial sites and hotels
- Any old sealant cut out fully, not covered over
- Arbo and Everbuild products
Read our cost guide and customer reviews.
How the job changes by surface
Linear gaps
Long, narrow gaps appear where walls meet slabs and ceilings. We seal them to the tested detail, with backing where it’s needed.
Door frames
Our work is the joint between frame and wall. Doors, seals and closers are for a door specialist and we’ll mention anything we notice.
Markethill: your questions answered
Do you cover smaller places like Markethill?
Yes. Markethill is within the area we cover, which takes in towns, villages and rural addresses. We work across all of Scotland. Just mention lanes, gates or anything else about the route when you book.
How do Scotland’s building regulations apply to fire-rated sealant in Markethill?
Scotland has its own building regulations, the Building (Scotland) Regulations, with their own technical handbooks. Fire-rated sealant has to go in to the product’s tested details, and we follow them. We don’t certify buildings or do fire risk assessments; your assessor or building control can tell you what’s required.
Can you tell me how many minutes the seal will last?
Ratings and certification sit with the product’s test evidence and whoever specified the work. We apply the specified product to the manufacturer’s details and list the locations and products for you.
Do you work in flats, HMOs and commercial buildings?
Yes. We regularly work in flats, HMOs, schools and offices while they’re in use. Out-of-hours work can be arranged where it’s needed.
Do you take out the old sealant first?
Yes. All of the old material is cut out and the joint cleaned before applying anything new.
Can ordinary silicone be used in a fire-stopping gap?
No. Where a fire-rated seal is needed, it has to be a product tested for that use.
Can you fill the gap behind a fire door frame?
Yes, if the gap is within the product’s tested range. We seal the frame-to-wall gap, not the door itself.
How long does the job take?
That depends on how much there is to do, but as a guide it takes from a few hours to a few days, depending on the number of gaps and the access. We will tell you when we quote.