Isle of Wight · England
Bathroom Resealing in Parkhurst
Bath, shower, basin, wet room, worktop and sink resealing for homeowners, landlords and businesses in Parkhurst. Fully insured, ARBOMaster approved and guaranteed for a year.
- A joint torn by a bath that flexes
- Damp behind the bath or under the tray
- Gaps between the worktop and the wall
How we handle bathroom resealing in Parkhurst
With over 20 years in the trade, we reseal baths, showers and kitchens in homes across Parkhurst. We’re fully insured ARBOMaster approved applicators, and the work comes with a 12-month guarantee. We work on shower trays & enclosures, sinks & splashbacks and baths, and people most often call us about leaks into the floor or ceiling below and water escaping at the shower enclosure.
In a village or hamlet like Parkhurst, homes are often older cottages and farmhouses alongside a few newer houses. Older walls and timber floors can move a little, and cracked grout and split sealant are often the first signs.
There’s a 12-month guarantee on every job.
- Place
- Parkhurst (PO30)
- Wider area
- Isle of Wight
- Guarantee
- 12 months on all our work
- Quote
- A clear price before any work starts
- Phone
- 0345 464 0079
- Page updated
- 26 October 2026
What happens if it’s left?
Bleach and mould sprays may lighten black marks for a while, but where mould is inside the silicone it generally comes back. Cutting it out and resealing with anti-fungal silicone is the fix that lasts. Older cottages and farmhouses around Parkhurst can have timber floors and frames, and water through a failed joint can rot timber if it’s left.
What it costs depends on the amount of work, how hard the old material is to remove and how easy the joints are to reach. We give a clear quote before we start, so you know where you stand.
Why book with us
- Approved under the ARBOMaster scheme
- We’re fully insured
- You choose the colour before work begins
- Every job guaranteed for a year
See our cost guide and what customers say.
What bathroom resealing looks like in Parkhurst
There are hotels and other places to stay in and around Parkhurst. Hotel bathrooms are part of our work as well as homes, and can be done room by room. Most of the South East has hard water, which leaves limescale on sealant, grout and fittings.
Around Parkhurst, as everywhere, bathroom resealing is only as good as the preparation behind it. Managing a site like Hunnyhill Primary School? Then washroom and kitchen sealant there needs the same care as at home, and schools and businesses are part of our work as well as homes.
Parkhurst is about 1 mile north of Newport, in the Isle of Wight. Our applicators cover bathroom resealing for homes and businesses in Parkhurst. Our area takes in 125 places across the Isle of Wight, from the larger towns to small villages. For nearby work, see our Portsmouth page.
Every address in PO30 is covered for bathroom resealing. Whether your property is on Dodnor Lane, Argyle Road and Sherwood Road or a nearby road, we can help. If you’re just outside Parkhurst, we cover Noke Common (1 mile north-west), Hunny Hill (1 mile south), Forest Side (1 mile south-west), Northwood (2 miles north) and Rew Street (2 miles north-west). We also work in nearby towns such as Ryde (6 miles east), Cowes (3 miles north), Sandown (8 miles south-east), Shanklin (8 miles south-east), Ventnor (9 miles south-east) and East Cowes (3 miles north). For island and remote addresses, a little more planning is needed, so mention it when you ask for a quote.
Local landmarks in Parkhurst
Around Parkhurst, our work takes us to homes and buildings near Medina College, Island Innovation VI Form Campus and The Stag pub and the streets around them. A little further out are Isle of Wight Bus & Coach Museum (1 mile south-east) and Carisbrooke Castle (2.1 miles south). For a walk, there’s Mill Hill and Briddlesford Nature Reserve.
How the job changes by surface
Sinks & splashbacks
Around the sink, we use a product suited to kitchens, including a food-safe sealant where that is needed. The joint is laid neatly so it’s easy to wipe.
Kitchen worktops & upstands
Worktop joints get wet and wiped every day. We seal them in a colour that suits the worktop.
Nearby places to Parkhurst
What else we do in Parkhurst
When something else is needed
Some problems need a builder, plumber or other trade rather than us:
- A tray that rocks until it’s re-bedded
- A leaking waste, trap or valve
- Failed grout lines across the wall
If in doubt, phone 0345 464 0079 or email us and we will say what we think.
Surfaces we seal
- Wet rooms
- Baths
- Shower trays & enclosures
- Kitchen worktops & upstands
- Basins & vanity units
- Sinks & splashbacks
Parkhurst questions
Do you cover smaller places like Parkhurst?
Yes, smaller places are covered as well as towns. We work across London and the South East. Just mention lanes, gates or anything else about the route when you book.
Do you work for hotels and guest houses in Parkhurst?
Yes, hotels and guest houses are among the places we work. A room-by-room programme keeps most rooms in use while the work goes on.
Will the old sealant be removed?
Yes. Sealing over the old bead is the commonest cause of early failure, and it’s something we never do.
Can you get rid of the black mould in my sealant?
Yes, we replace the mouldy bead. Sprays can fade the marks, but cutting it out and resealing is what lasts. Airing the room well helps stop it returning.
What should I tell you?
Just the basics: where it is, what you’ve noticed and how we reach it. After that, simply phone 0345 464 0079 or drop us an email.
How long does it take to reseal a bath or shower?
It depends on how many joints there are and how much old sealant has to come out. Allow a couple of hours for a typical bath or shower.
Do I need to be at home?
If the work is inside, we need someone to let us in. Once we have agreed the job, you do not need to watch us work.
Do you guarantee your resealing?
Yes. We give a 12-month guarantee on every job, and we’re ARBOMaster approved applicators.
Should I try it myself first?
Some sealant jobs are within reach of a careful DIYer, like a short, easy-to-reach joint indoors. Where it goes wrong is sealing over the old bead, working on a wet joint or overloading the gap.
What a professional job adds is preparation and the right product. We take joints back to clean, dry surfaces, and the sealant is chosen for how the joint moves and where it is, then guaranteed for a year.
What we do, step by step
On the day, there’s very little for you to do. Show us the job and we will take it from there. The work itself takes a couple of hours for a single bath or shower from start to finish. In a small place like Parkhurst, access is normally the main thing to plan. For outside work, also let us know about exposed walls and any outbuildings involved.
- First, each joint is checked for movement and signs of water.
- Every trace of the old bead is removed, including the thin smear on the tiles.
- Joints are degreased and any mould is treated.
- With the joint dry, and any bath loaded with water, a single bead of anti-fungal silicone is applied.
- The bead is tooled smooth and you are told the cure time, generally around 24 hours.
Preparing for the visit
- Keep children and pets away from the work area
- Tell us if parking is tricky
- Tell us about any previous sealing or DIY attempts
Getting a quote
Want a quote for bathroom resealing? Please ring 0345 464 0079 or email us and tell us about the job. We’ll explain what we’d do and send you a clear quote before any work starts.
Read more
Work for landlords, hotels and businesses
In hotels, rooms out of use cost money, so the work can be planned room by room around your bookings where we can. Hotel work is part of what we do, alongside homes and businesses.
Businesses can book us for washrooms, kitchens, offices and more. For commercial premises, we can talk through working times when we quote.
Aftercare tips
So the new joints stay in good condition:
- Keep an eye on the corners, where splits start
- Do not let bottles sit on the bead
- Use gentle cleaners on the silicone
- Keep scourers and sharp tools away from the bead
Don’t stand bottles along the bead, as they hold water against it. A quick squeegee after showering keeps water from sitting on the joint.
There’s no need to wait for a full refurbishment. Like paintwork, sealant needs renewing from time to time, and replacing it when it fails protects the rest of the room.