Hampshire · England
Regrouting in Hordle
Professional regrouting in and around Hordle, with every bit of old sealant taken out first and a one-year guarantee.
- Grout in a colour the owner wants to change
- Cracked grout along the bath or tray
- Discoloured grout on otherwise sound tiles
Regrouting in Hordle, done properly
Stained, crumbling or cracked grout can make a sound bathroom look tired. With regrouting, the tiles stay and only the grout is renewed, so there’s no stripping out and no new tiles to choose. We work on kitchen splashbacks, shower walls and bathroom wall tiles, and people most often call us about cracked grout along the bath or tray and a grout colour that no longer suits the room.
In a smaller place like Hordle, homes are mostly houses and bungalows rather than flats, from older cottages to newer builds. Sealant and grout wear out here just as they do in a big town.
We stand behind the work with a one-year guarantee, so you’re not left on your own once the job is done.
- Location
- Hordle (SO41)
- Region
- Hampshire
- Cover
- 12 months on all our work
- Price
- A clear quote up front
- Telephone
- 0345 464 0079
- Last updated
- 26 October 2026
Do you need regrouting in Hordle?
Some grout fails because it was mixed or laid badly. If it was mixed too wet or not pressed in firmly tends to wash out early.
Any of these means the joints need attention:
- Kitchen splashback grout stained by grease
- Grout that makes sound tiles look old
- Gaps where the shower grout has gone
- Grout in a colour the owner wants to change
Managing a site like Hordle CofE (VA) Primary School? Then washroom and kitchen sealant there needs the same care as at home, and schools and businesses are part of our work as well as homes.
Comparing quotes
- How the colour is chosen
- What happens if they find a problem under the old sealant
- The length of the guarantee
- Who does the work, and how experienced they are
Also in Hordle
Different surfaces, different methods
Wet rooms
Wet rooms have water across the floor, so sound grout really matters. We check the tiles first.
Kitchen splashbacks
Kitchen grout collects grease and food splashes. Once it’s stained, new grout is often the only fix.
Regrouting in Hordle: local notes
Hordle is close to the coast. Near the coast, holiday lets and guest houses can see bathrooms used by one guest after another, and sealant and grout that work that hard wear out sooner. Hard water is the norm across most of the South East, which leaves limescale on sealant, grout and fittings, and it has to be cleaned off before new sealant goes in.
For landlords with property near New Milton station, a regrout while the flat is empty is quicker than working around a tenant. In the older streets around Church of All Saints, bathrooms in older houses have often been refitted more than once, with sealant laid over sealant.
Hordle is about 3 miles west of Lymington, in Hampshire. Hordle gets the same service as everywhere we cover: old sealant removed completely, careful preparation and a 12-month guarantee. Hordle is one of 683 towns and villages in Hampshire where we work. For nearby work, see our Southampton page (15 miles or so).
All of SO41 is covered for regrouting, from the main roads to the quietest streets. Streets in the area include Yerville Gardens, Acacia Road and Woodlands, all of which we cover. Neighbouring places we cover for regrouting include Downton (1 mile south), Leagreen (1 mile south), Ashley (1 mile west), Tiptoe (2 miles north) and New Milton (2 miles west). We also work in nearby towns such as Totton (12 miles north-east), Lymington (3 miles east), Hythe (12 miles north-east), Ringwood (9 miles north-west), Dibden Purlieu (11 miles north-east) and Marchwood (12 miles north-east).
Landmarks near Hordle
Locally, jobs take us to homes and businesses close to The Arnewood School and the streets around them. The closest station to Hordle is New Milton station, about 1.7 miles west of the centre. Well-known places in the area include Sammy Miller Motorcycle Museum (2.4 miles west) and Highcliffe Castle (4.4 miles west). Not far away are Milford on Sea LNR.
Hordle questions
I let a flat near New Milton station. Can you help?
Yes, we work for landlords and agents. You can ring 0345 464 0079 or send us an email with the address and a few details, and we’ll give you a fixed price before work begins.
Do you cover Hordle for regrouting?
Yes. We work across London and the South East, and Hordle is part of that. Just call 0345 464 0079 or email us with a few details of the job, and we’ll send you a clear quote.
What guarantee comes with the work?
Our one-year guarantee applies to all our work, and we’re fully insured.
How long does the job take?
That depends on how much there is to do, but as a guide it takes a few hours for a shower enclosure, longer for a whole room. We will tell you when we quote.
When can I use the shower again?
You’ll get a clear time from us before we go. The grout and sealant both need to cure before they get wet.
Are you an approved applicator?
Yes. We hold ARBOMaster approved applicator status, and we are fully insured.
How much does regrouting cost in Hordle?
It depends on the job, so we quote each one individually. For a quick quote, ring 0345 464 0079 or email us and tell us what needs doing and where.
Is regrouting a chance to pick a new grout colour?
Yes. Many customers do. Darker grout can hide marks and lighter grout gives a fresher look.
Landlord and commercial work in Hordle
Water getting past a failed joint can damage the building, which is a bigger problem in a rented property. Resealing at the right time is simple maintenance that we can handle for you.
Businesses can book us for washrooms, kitchens, offices and more. For commercial premises, we can talk through working times when we quote.
How it works
A visit follows a simple pattern: we look at the joints together, mask and protect the surrounding surfaces, carry out the job and clear up. It normally takes a few hours, or longer for a fully tiled room. Parking around Hordle is generally easier than in a town centre, but mention any lanes, gates or long drives. For outside work, side access and the height of the joints help us plan.
- Every tile area is checked for hollow or loose tiles first.
- The old grout is removed to an even depth.
- The joints are vacuumed clean.
- New grout is pressed into the joints and the tiles are cleaned.
- We finish with silicone in the moving joints.
Preparing for the visit
- Mention any parking rules near the property
- Let us know about stairs, lifts or work at height
- Let us know if you’ve seen damp or leaks
How to get a quote
The more we know about the job, the more useful the quote. Let us know the location, the problem and roughly how many joints, and add pictures by email if you can.
Related advice
What affects the cost of regrouting
For a quick quote, just ask. The main things that affect it are:
- How many areas need sealing
- The type of sealant required
- Access and height
- How much there is to do
The cost depends on the size of the job, how hard the old material is to remove and access to the work. We give a clear quote before we start.
Asking for a quote
What to tell us when you ask for a quote:
- Whether it’s a home or a business
- A few photos by email, if you can
- How many joints, rooms or windows are involved
- Any previous sealing or DIY work
For a quote, phone 0345 464 0079 or drop us an email and tell us where the job is and what the problem looks like. You will have a clear quote before we start.
Honest limits
To be straight with you, some problems need a different trade:
- Cracked or broken tiles
- A leaking wet room membrane
- Water coming from plumbing rather than grout
If in doubt, phone 0345 464 0079 or drop us an email and we will say what we think before you book.
Joints and surfaces we work on
- Bathroom floors
- Shower walls
- Bathroom wall tiles
- Tiled floors
- Kitchen splashbacks
- Wet rooms
Can I do it myself?
If you are set on DIY, put the effort into preparation: take out all the old sealant, make sure the joint is clean and dry, and give it the full cure time. If it fails, we can still redo it.
What a professional job adds is preparation and the right product. We take joints back to clean, dry surfaces, and the sealant is chosen for how the joint moves and where it is.