Essex · England
Bathroom & kitchen resealing in Ballards Gore, Essex
Professional bathroom resealing in and around Ballards Gore, with every bit of old sealant taken out first.
- Gaps between the worktop and the wall
- Smears of silicone across the tiles
- A reseal done over the top of the old bead
Should I try it myself first?
The biggest DIY mistake is sealing over old sealant. New silicone won’t bond to old, so it peels away and traps moisture behind it. Everything old must be removed first.
Overfilling a joint is a classic DIY mistake. A thick, smeared bead looks untidy and doesn’t move well, and getting the depth right matters as much as the look.
About our bathroom resealing in Ballards Gore
Before a bath is sealed, it’s filled with water. A full bath sits slightly lower than an empty one, so the new joint isn’t pulled apart the first time it’s used. It’s a small step that rushed reseals tend to skip. If you are dealing with a messy, uneven bead from a previous reseal and water getting behind the bath panel, we can put it right, on shower trays & enclosures, basins & vanity units and wet rooms alike.
Around Ballards Gore, it’s houses and cottages rather than flats, some with bathrooms tucked into older rooms or extensions. The work is the same as anywhere: everything old comes out before the new sealant or grout goes in.
Our work is backed for twelve months.
- Where
- Ballards Gore (SS4)
- Region
- Essex
- Guarantee
- A year, on every job
- Quote
- A clear price before any work starts
- Telephone
- 0345 464 0079
- Updated
- 26 October 2026
Also in Ballards Gore
Bathroom resealing in Ballards Gore: local notes
Most of the South East has hard water, so limescale builds up on sealant, grout and fittings, and it has to be cleaned off before new sealant goes in.
Letting a property close to Rochford station? Then fresh sealant around the bath, shower and sink between tenancies helps a property present well and keeps leaks at bay.
Ballards Gore is about 2 miles north-east of Rochford, in Essex. Jobs in Ballards Gore get the same care as everywhere else we work: old sealant removed completely, careful preparation and a one-year guarantee. Our Essex coverage runs to 644 places, and Ballards Gore is one of them. Chelmsford is on our list too, around 15 miles away.
All of SS4 is covered for bathroom resealing. We also cover the places around Ballards Gore: Canewdon (1 mile north), Creeksea (3 miles north-east), Ostend (4 miles north-east), Althorne (4 miles north) and Latchingdon (5 miles north). We also work in nearby towns such as Chelmsford (15 miles north-west), Basildon (13 miles west), Maldon (9 miles north), Canvey Island (9 miles south-west), Billericay (14 miles west) and Rayleigh (6 miles west).
What’s near Ballards Gore
In Ballards Gore, that means homes and buildings near The Shepherd and Dog pub and the streets around them. For rail, the closest station is Rochford station, roughly 2.4 miles south-west of the centre. Well-known places in the area include Rayleigh Windmill Museum (2.2 miles south-west) and Southend University Hospital (4.2 miles south-west). Green spaces nearby include Lion Creek and Lower Raypits.
Honest limits
It helps to know what we cannot do:
- A cracked shower tray or bath (that needs repair or replacement)
- A leaking waste, trap or valve
- Cracked or missing grout between tiles (that is regrouting)
If you’re not sure, just call 0345 464 0079 or drop us an email and we will give you a straight answer before you book.
Surfaces we seal
- Baths
- Kitchen worktops & upstands
- Wet rooms
- Shower trays & enclosures
- Basins & vanity units
- Sinks & splashbacks
Ballards Gore: your questions answered
Do you work for landlords with property near Rochford station?
Yes, rental work is part of what we do. Just call 0345 464 0079 or drop us an email and tell us about the property, and we’ll send you a clear quote.
Do you cover smaller places like Ballards Gore?
Yes, Ballards Gore is covered. We work across London and the South East, from towns to the smallest places. Longer journeys are simply planned in advance.
What does bathroom resealing cost?
There’s no set price, as it depends on the job: how much there is, what’s there now, how we reach it and what it needs. You will get a clear quote before work begins.
What do you put in the joint?
Each joint gets the product that suits it. Where it moves, gets wet or faces the weather makes a difference, and we will tell you what we’re using.
Can you just seal over the old silicone?
No. Fresh silicone can’t stick to the old bead, so it peels away and hides mould and water. All the old sealant comes out first.
Do you have insurance?
Yes, we’re fully insured for domestic and commercial work.
What colours of sealant can you use?
White, clear and a range of colours are available. Where the joint is on show, we match it to the surface.
Will you leave a mess?
No. We work neatly, protect the area around the joints and tidy up afterwards.
How it works
Most of a good job is in the preparation, so that is where we spend the time. Every joint is cleaned and dried before new material goes in. In total, it normally takes half a day or less for one room, longer when the kitchen is included. Somewhere as small as Ballards Gore, access is often the only tricky part. If the job is outside, mention outbuildings, exposed walls and how to reach them.
- First the area is protected and every bit of old sealant removed, including the film left on the tiles.
- Next, the joint is cleaned and any mould is treated.
- The joint is left to dry, and baths are filled with water first.
- A single bead of anti-fungal sanitary silicone is applied and tooled smooth.
- We tidy up and give you the cure time, generally around 24 hours.
Getting ready for the visit
- Clear items away from the joints we’re working on
- Tell us if parking is tricky
- Mention any leaks or damp you’ve noticed
Getting a quote
Call for a quick quote, or send an email if you’d rather. Tell us about the joints that need doing and we will talk you through the work before giving you a price.
Related advice
Why it’s worth doing now in Ballards Gore
You don’t need a new bathroom because the sealant looks bad. A new bead often brings the whole room back. If something else is wrong, we’ll tell you. Where a wall is exposed, as many are in small places like Ballards Gore, wind-driven rain gets into any failed joint, and older walls, once damp, take a long time to dry.
A few things move the cost up or down: the old material and how easily it comes out, whether mould needs treating, and whether we need extra access for height. Your quote takes all of that into account.
Why choose Mr Mastic in Ballards Gore
- Neat joints and a tidy finish
- ARBOMaster approved applicator
- Old sealant always removed completely
- Sanitary silicone with an anti-fungal additive in wet areas
See our cost guide or customer reviews.
When to call us in Ballards Gore
Not every tube in the shop is meant for a shower. Acrylic caulk and general-purpose sealants aren’t designed for a joint that’s wet every day, so they crack, discolour or grow mould quickly. Wet areas call for a sanitary silicone with an anti-fungal additive.
The most common problems we see are:
- A joint torn by a bath that flexes
- Cracked, shrunken or lifting silicone
- Black mould in the silicone that will not clean off
- A messy, uneven bead from a previous reseal
Managing a site like King Edmund School? Then we reseal washrooms and kitchens in schools and businesses as well as homes.
Comparing quotes
- Is VAT in the price?
- How the surfaces are prepared before sealing
- What happens if they find a problem under the old sealant
- The length of the guarantee
How to look after the new joints
A little care helps the new joints last. Our advice:
- Look for lifting corners and small gaps now and then
- Open a window or run the fan so the room dries
- Squeegee the walls and tray after use
- Wait for the cure time we give you
Good ventilation does more than any cleaner. Use the fan, or open a window, while you bathe and for a while afterwards, so the bead dries out between uses.
Each shower pushes a little more water through a failed joint. Left alone, it soaks into the floor, the wall behind the tiles or the ceiling below. Early resealing closes the gap before damage is done.
Landlord and commercial work in Ballards Gore
Water getting past a failed joint can damage the building, which is a bigger problem in a rented property. Keeping joints in good order is simple maintenance that we can handle for you.
For anyone letting property in or around Ballards Gore, jobs at different addresses can go on one quote. Just tell us the addresses and what each one needs.