Essex · England
Tiptree External Mastic
Movement joints in Tiptree need attention? We cut out the old, prepare the joints and apply the right sealant.
- Joints pointed up with cement by mistake
- Panel joints letting water in
- Plants rooting in failed movement joints
How the job changes by surface
Cladding and façade panels
Metal and composite panels move a lot with temperature, so the joint sealant has to cope with frequent movement. The sealant is chosen with that in mind.
Brickwork movement joints
Brick moves with heat and moisture, and grows a little over time. The movement joint takes that up, so the sealant in it must stay soft and stretchy.
How we handle external mastic in Tiptree
Getting the depth right is half the job. Backing rod controls how deep the sealant goes and keeps it off the back of the joint, leaving it bonded to two faces so it can move with the wall. We work on façade panels, joints between brick and frames and concrete & block, and the jobs we see most are weeds or debris growing in open joints and rigid filler in a joint that should flex.
In a smaller place like Tiptree, some homes face open ground, so exposed walls and rooflines take more wind-driven rain. That’s where gutter joints and wall joints tend to fail first.
We guarantee the work for a year. If something is not right with it in that time, tell us and we’ll put it right.
- Where
- Tiptree (CO5)
- Region
- Essex
- Guarantee
- A year, on every job
- Quote
- A clear price before we start
- Phone
- 0345 464 0079
- Last updated
- 26 October 2026
Aftercare tips
How long the joints last depends on use and care. Here’s what we suggest:
- Act on the first splits you see
- Leave the joints unpainted unless we’ve said otherwise
- Make sure movement joints are not pointed over
- Check external joints each spring
If you have more work done on the wall, such as new render, cladding or an opening, show the contractor the movement joints. They should be kept open and resealed, not filled.
Act while the splits are small. At that stage it’s a simple cut out and reseal.
Should I try it myself first?
Not every job suits DIY: work at height, external movement joints, fire-rated sealant and large areas need the right product, the right access and the right method.
Overfilling a joint is a classic DIY mistake. A heavy bead looks messy and copes badly with movement, and the joint depth matters as much as the finish.
Also near Tiptree
Also in Tiptree
The process
Every visit runs the same way: we check the joints, mask and protect the surrounding surfaces, do the work and clear up. It normally takes anything from a few hours to several days, depending on the building. In a smaller place like Tiptree, parking is seldom the issue; lanes, gates and long drives are worth mentioning. If the job is outside, tell us about side access and how high the joints are.
- We inspect the joints and agree which need resealing and how they’ll be reached.
- Old sealant and any debris are cut and raked out.
- We clean both faces of the joint and prime them where the product calls for it.
- Closed-cell backing rod is fitted to set the depth and stop three-sided bonding.
- The new sealant, chosen to suit the brick or render, is applied and tooled to a neat finish.
How to prepare
- For business premises, tell us about site rules or sign-in
- Let us know about parking restrictions
- Plan for the work area to be out of bounds to pets and children
How to get a quote
We quote each job on its own, so start by telling us what you need. Simply ring 0345 464 0079 or email us and describe the job.
Advice
Walls and rooflines in Tiptree
With historic houses such as Layer Marney Tower (about 2.1 miles east) nearby, there’s older building stock in the area around Tiptree as well as newer homes. In older buildings, older brick and stone need a sealant that suits them, at the right joint depth. London and the South East are among the drier parts of the UK, though outdoor sealant still has to go onto a dry joint, so the forecast decides the day.
Schools such as St Luke's Church of England Controlled Primary School are buildings too, and its movement joints, gutters and trims need looking after like any other building’s. Letting a property close to Kelvedon station? Then split movement joints are easy to miss on a rental until damp shows inside. For an older house near a landmark such as Church of St Luke, an extension built onto an older house moves differently, and the joint between them takes the strain.
Tiptree is about 5 miles east of Witham, in Essex. Jobs in Tiptree get the same care as everywhere else we work: the old material taken out, joints prepared properly and a 12-month guarantee. Our Essex coverage runs to 644 places, and Tiptree is one of them. For nearby work, see our Chelmsford page (12 miles or so).
All of CO5 is covered for external mastic, from the main roads to the quietest streets. You’ll find streets such as Church Road, Station Road and Grosvenor Close. We also cover Windmill Hill (1 mile west), Tiptree Heath (1 mile south-west), Messing (2 miles north), Layer Marney (2 miles north-east) and Feering (3 miles north-west). We also work in nearby towns such as Colchester (8 miles north-east), Chelmsford (12 miles south-west), Braintree (9 miles north-west), Maldon (7 miles south-west), Witham (5 miles west) and Camulodunum (7 miles north-east).
Around Tiptree
Around Tiptree, our work takes us to homes and buildings near The Anchor Public House, Thurstable School and Tiptree Parish Field. The nearest railway station is Kelvedon station, roughly 2.8 miles north-west. Nearby you’ll also find Birch Castle (3.7 miles north-east) and Anchor Press Museum (within half a mile east). Open spaces near Tiptree include Tiptree Heath Nature Reserve.
When it isn’t the sealant
Honest advice matters more to us than a booking, so here’s what sealant can’t fix:
- Movement that’s more than a sealant joint can take
- Cracking across the wall rather than at a joint
- Render that’s blown, hollow or coming away
Not sure which it is? You can phone 0345 464 0079 or drop us an email and we will tell you honestly.
What we seal
- Façade panels
- Brickwork movement joints
- Render & cladding joints
- Joints between brick and frames
- Concrete & block
- Copings & trims
Why act early in Tiptree
Running new sealant over the old bead rarely lasts. The new layer cannot bond properly to old, weathered material, so we always take the old sealant out. Around Tiptree, water from a failed joint in an older home can soak into timber and plaster, which is far harder to put right than the sealant itself.
A few things move the cost up or down: the old material and how easily it comes out, whether mould needs treating, and whether the work is at height. Your quote takes all of that into account.
What you get with us
- A sealant colour to suit the surroundings
- You choose the colour before work begins
- 4.9 on Google from 180+ five-star reviews
- ARBOMaster approved applicator
Take a look at how sealant jobs are priced and what customers say.
Questions from Tiptree
Do you work for landlords with property near Kelvedon station?
Yes. We work for letting agents and landlords as well as householders, and several properties can be quoted together. Just ring 0345 464 0079 or email us with the address and what needs doing, and we’ll give you a clear price.
Will you come out to Tiptree?
Yes, we do. We work across London and the South East, from towns to the smallest places. The journey is planned ahead, so it helps to know about access.
Can a movement joint be filled with mortar?
No, not if it’s a movement joint. Pointing it stops it working. We’ll reseal it with a flexible sealant.
Can I do it myself?
That depends on the joint. Work at height, movement joints, fire-rated gaps and large areas are best left to a professional, while a short indoor joint may be within reach.
What colours does the sealant come in?
We aim for a joint that suits the wall rather than one that jumps out. We will talk through colour options before work begins from the range available.
Can you work on commercial sites?
Yes. We’ve worked for hotels, offices and other businesses and we are fully insured.
Do I have to be there?
For indoor joints, yes, someone needs to let us in. After that, you can carry on with your day.
Do you have insurance?
Yes, we’re fully insured for every job we do.
Landlords, agents and businesses in Tiptree
Hotels need rooms back in use, so we plan the work room by room around your bookings where we can. We’ve worked in hotels as well as homes and businesses.
Letting agents often deal with us directly. Send the address, what’s needed and the access arrangements and we’ll give you a quote.