Highland · Scotland
Bathroom Resealing in Watten
Bathroom resealing in Watten from a team with over 20 years’ experience. Rated 4.9 on Google from 180+ five-star reviews.
- Black mould in the silicone that will not clean off
- A bead that has pulled away from the tiles
- Splits where the tray meets the wall
How we handle bathroom resealing in Watten
With over 20 years in the trade, we reseal baths, showers and kitchens in homes across Watten. We’re fully insured ARBOMaster approved applicators, and every job carries our 12-month guarantee. Common call-outs are for water escaping at the shower enclosure and leaks into the floor or ceiling below, on wet rooms, basins & vanity units and shower trays & enclosures.
Being further from a city does not change the work: everything old is cut out, the joints are cleaned and dried, and new sealant or grout goes in. The journey and access are simply planned in advance.
All our work is covered by a 12-month guarantee, wherever you are in Highland.
- Where
- Watten (KW1)
- Wider area
- Highland
- Guarantee
- 12 months on all our work
- Price
- Quoted before any work starts
- info@mrmastic.co.uk
- Page updated
- 26 October 2026
Watten homes and their sealant
Scottish Water supplies are generally soft, so limescale is less of a problem than in hard-water areas. But mould still grows into sealant and grout in a room that doesn’t dry out. Private landlords in Scotland must be registered and meet the Repairing Standard, which covers keeping fixtures and fittings in a reasonable state of repair. Failed sealant around a bath or shower is worth sorting between tenancies.
For jobs in and around Watten, choosing the right material for each joint is as important as a tidy finish. Around Watten, as everywhere, bathroom resealing is only as good as the preparation behind it.
Watten is about 12 miles south-east of Thurso, in Highland. Jobs in Watten get the same care as everywhere else we work: old sealant removed completely, careful preparation and a 12-month guarantee. Watten is one of 253 towns and villages in Highland where we work for bathroom resealing.
We cover every part of the KW1 postcode area for bathroom resealing and the streets around it. That includes homes and businesses on Station Road, Henderson Square and Achingale Place and the roads around them. Close by, we work in Gillock (3 miles north-west), Hastigrow (4 miles north), Bower (5 miles north), Reiss (5 miles east) and Haster (6 miles east). We also work in nearby towns such as Thurso (12 miles north-west), Wick (8 miles east) and Castletown (9 miles north). For island and remote addresses, a little more planning is needed, so let us know when you get in touch.
What’s near Watten
For a walk, there’s Loch Watten.
Other services in Watten
FAQs for Watten
Is bathroom resealing in Watten guaranteed?
All our work, in Watten and everywhere else, comes with a 12-month guarantee. We’re fully insured, and an ARBOMaster approved applicator.
Do you cover Watten for bathroom resealing?
Yes, Watten is within the area we cover. We work across all of Scotland. You can send an email to info@mrmastic.co.uk and tell us what needs doing, and we will send you a clear quote.
Does someone need to be in?
That depends on where the joints are. For work indoors, someone needs to let us in.
Can I do it myself?
Sometimes. The key is preparation: remove all the old material and work on a clean, dry joint. We can always put it right if it fails.
Is it OK to put new sealant on top of the old bead?
No. A bead laid over old silicone soon starts to come away. Every trace of the old bead is removed first.
How long does the new silicone need before I use the shower?
After around 24 hours in most cases. We will tell you the cure time for the product we used.
How long will the resealing take?
That depends on the number of joints and the state of the old sealant. For most single baths or showers, allow a couple of hours.
Do you have insurance?
Yes. Full insurance covers our work.
Why act early in Watten
Tired sealant is not a reason to replace a bath or shower. Replacing the joint is normally all it takes. If something else is wrong, we’ll tell you. Exposed walls in smaller Scottish places take a lot of wind and rain, and damp in stone or harled walls takes a long time to dry once water gets behind a joint.
Some things make a job bigger or smaller: the old material and how easily it comes out, whether mould needs treating, and whether the work is at height. We take all of that into account in your quote.
What you get with us
- A sealant colour to suit the surroundings
- Colour agreed with you before work begins
- ARBOMaster approved applicator
- Tidy, careful work
How the job changes by surface
Sinks & splashbacks
The edge of an inset sink is a common place for water to get under the worktop. We reseal the visible edge of the sink where it has failed.
Shower trays & enclosures
Water often gets past the wall profile of a shower enclosure. We reseal it along with the base of the enclosure, sealing the side the enclosure’s instructions call for.
The process
On the day, there’s very little for you to do. Point us to the joints and we’ll get on with it. The job generally takes two to three hours for a typical bath, depending on how much old sealant there is, including the tidy-up. Around Watten, distance and access matter more than parking. Let us know how to find you and how to reach the joints, and the visit is planned around that.
- First the area is protected and every bit of old sealant removed, including the film left on the tiles.
- Next, the joint is cleaned and any mould is treated.
- We let it dry fully and fill the bath with water before sealing.
- We apply anti-fungal sanitary silicone in one even bead and tool it neatly.
- Finally we tidy up and explain the cure time before we leave.
Before we arrive
- Tell us about any water getting in
- For business premises, tell us about site rules or sign-in
- Mention any parking rules near the property
Ask for a quote
Want a quote for bathroom resealing? Please email us at info@mrmastic.co.uk and tell us about the job. We will explain what we’d do and give you a clear quote before work begins.
Related advice
DIY versus a professional finish
A DIY attempt doesn’t rule out a professional job. We remove it and do the joint properly, so just mention it when you contact us.
What a professional job adds is preparation and the right product. Joints are cleaned back to sound surfaces and dried, and the sealant is chosen for how the joint moves and where it is, then guaranteed for a year.
Landlord and commercial work in Watten
For anyone letting property in or around Watten, jobs at different addresses can be quoted together. Just tell us the addresses and what each one needs, and photos by email help.
Failed sealant is one of the commonest items on a check-out report. Several properties can go on one quote.
What affects the cost of bathroom resealing
We don’t publish a price list, because no two jobs are the same. What we look at:
- The number of rooms or windows
- Whether old sealant or filler has to be cut out
- The product the joint needs
- Any working-time requirements on site
Homes and businesses are quoted the same way: the amount of work, the access and the products needed. Call for a quick quote and we’ll explain what it covers.
Helping us quote
When you call or email, these details help:
- The rough size of the job
- Any previous sealing or DIY work
- Where the job is, and your postcode
- Whether it’s a home or a business
For a quick quote, get us on the phone, or send an email if you’d rather. Describe what needs sealing and we will explain what’s involved before giving you a price.
Looking after it afterwards
A little care helps the new joints last. We recommend:
- Don’t leave water standing on kitchen joints
- Run the extractor fan during and after every shower
- Wait for the cure time we give you
- Clean with a mild bathroom cleaner and a soft cloth
Clean the silicone with care: a mild bathroom cleaner and a soft cloth is enough. Avoid scouring pads and anything sharp, and a nicked bead lets mould in sooner.
Worktop joints fail quietly. Water gets behind the upstand and into the edge of a laminate worktop, where it can make the board swell. Resealing before that happens protects the worktop.