Kent · England
Regrouting in Highstreet, Kent
Tiled areas in Highstreet need attention? We cut out the old, prepare the joints and apply the right sealant, and the work is guaranteed for a year.
- Old grout in a dated colour
- Shower grout that has worn away
- Stained grout that cleaning will not shift
Regrouting in Highstreet: local notes
Highstreet is within about 2 miles of the coast. Near the coast, holiday lets and guest houses can see bathrooms used by one guest after another, which wears sealant and grout out faster than in a quiet home. Hard water is the norm across most of the South East, which leaves limescale on sealant, grout and fittings, and it has to be cleaned off before new sealant goes in.
Around Highstreet, as everywhere, regrouting is only as good as the preparation behind it.
Highstreet is about 3 miles south-west of Whitstable, in Kent. Highstreet gets the same service as everywhere we cover: the old material taken out, joints prepared properly and a 12-month guarantee. Our Kent coverage runs to 922 places, Highstreet among them. You can also see our page for Chelmsford, about 36 miles away.
Jobs for regrouting in ME13 is quoted and booked the same way as anywhere else. Whether your property is on Thanet Way and Highstreet Road or anywhere close by, our applicators can take on the job. If you’re just outside Highstreet, we cover Waterham (1 mile west), Dargate (1 mile south-west), Seasalter (1 mile north), Hernhill (2 miles south-west) and Slutshole (2 miles south-west). Further out, we also cover Ashford (14 miles south), Canterbury (5 miles south-east), Sittingbourne (11 miles west), Whitstable (3 miles north-east), Faversham (4 miles west) and Herne Bay (7 miles north-east).
Landmarks near Highstreet
We work in homes and buildings around Foxes Cross Bottom. The closest station to Highstreet is Whitstable station, about 3 miles north-east. Well-known places in the area include Whitstable and Tankerton Hospital (3.6 miles north-east) and Tankerton Castle (3.3 miles north-east). Not far away are Blean Woods RSPB Reserve.
Regrouting for homes and businesses in Highstreet
Stained, crumbling or cracked grout can make a sound bathroom look tired. With regrouting, the tiles stay and only the grout is renewed, so there’s no stripping out and no new tiles to choose. We work on kitchen splashbacks, tiled floors and bathroom floors, and common reasons people get in touch are greasy, stained grout behind the hob and grout washed out of a shower.
For a small place like Highstreet, regrouting is planned like any other job: the journey and access are simply agreed in advance. Once we’re there, the bathroom or kitchen gets the same care as anywhere else.
Big or small, it’s backed by our 12-month guarantee in Highstreet and across Kent.
- Place
- Highstreet (ME13)
- Wider area
- Kent
- Cover
- 12 months on all our work
- Quotes
- A clear price before work begins
- Phone
- 0345 464 0079
- Updated
- 26 October 2026
FAQs for Highstreet
I let a flat near Whitstable station. Can you help?
Yes. We work for landlords and agents as well as homeowners. Just phone 0345 464 0079 or email us with the address and what needs doing, and we will send you a clear quote.
Do you cover smaller places like Highstreet?
Yes, we do. Our work covers London and the South East, from towns to the smallest places. The journey is planned ahead, so it helps to know about access.
Is it messy?
We keep the work tidy. Nearby surfaces are protected.
When can I use the shower again?
The wait depends on the materials and how warm the room is. We’ll give you a time to follow at the end of the visit.
Can you regrout if a few tiles are loose?
If tiles are loose, something behind them has normally failed. Regrouting alone is not the answer, and we’ll tell you before any work starts.
Is regrouting a chance to pick a new grout colour?
Yes. With the old grout removed, the new colour fills the whole joint, not just the surface.
What do you put in the joint?
Each joint gets the product that suits it. Movement, water and weather all affect the choice.
Is resealing included with regrouting?
Normally we do both. Grout and sealant do different jobs, so we renew both and it’s all in the quote.
How to look after the new joints
After the cure time, these simple habits help:
- Use gentle cleaners on grout
- Get any tile that moves checked promptly
- Run the extractor fan during and after a shower
- Look at the sealant in the corners now and then
Before we leave, you’ll know when the shower can be used. Stick to that time, and avoid scrubbing the new grout hard for the first few days.
If grout in the shower is washing out, act soon. Each shower drives water into the open joints and it can end up in the wall or the ceiling below.
Different surfaces, different methods
Corners and edges
Internal corners move, so they get silicone, not grout.
Kitchen splashbacks
Splashback grout picks up grease and cooking stains. Stained grout is best replaced.
Leave it or put it right?
Grouting over old grout rarely lasts. A thin skin on top tends to break off, taking any repair with it. Raking out to a consistent depth gives the new grout something to hold. In a small place like Highstreet, homes can be exposed to wind and rain, which finds any gap, and older walls, once damp, take a long time to dry.
The cost reflects the work involved, not guesswork. That’s why we ask a few questions first and give you a clear price before we start.
Why choose Mr Mastic in Highstreet
- More than 20 years in sealant work
- An ARBOMaster approved applicator
- Quality sealants from Arbo and Everbuild
- We never seal over old sealant
Read our cost guide and customer reviews.
How it works
Good joint work is mostly preparation, and we do not rush it. Joints are cleaned back and dried before anything new goes in. In total, it generally takes a few hours for a shower enclosure, longer for a whole room. Somewhere like Highstreet needs a little journey planning: tell us about narrow lanes, gates, long drives and where we can park. Everything for the job comes with us, so a second trip is avoided where possible.
- First we agree what’s being done and flag any loose tiles.
- Grout is raked out without chipping the tiles.
- The joints are cleaned out and vacuumed.
- We grout the joints and wipe the tiles clean.
- We renew the silicone at the corners and edges.
How to prepare
- Tell us if parking is tricky
- Where the joints are inside, avoid wetting them before we arrive
- On commercial sites, let us know about site rules
Ask for a quote
Need a quote? Please call 0345 464 0079 or send us an email and tell us about the job. You will know what we plan to do, and what it will cost, before any work begins.
Read more
Quotes for regrouting in Highstreet
For a quick quote, just ask. What matters most is:
- Whether there’s mould to deal with
- The type of sealant required
- The number and length of the joints
- The old material and how stubborn it is
We do not show prices on the website, because each job is priced on what it involves. Call for a quick quote.
Asking for a quote
Before you ask for a quote, have a think about:
- Pictures of the joints, sent by email
- Whether it’s a home or a business
- How we’d reach the joints
- How many joints, rooms or windows are involved
Call for a quick quote, or email us if that’s easier. Tell us about the joints that need doing and we will talk you through the work and give you a clear price.
Signs you need regrouting in Highstreet
Grout is porous, so water, soap and grime soak into it. Given time, it discolours and begins to break down and showers that get daily use suffer most.
It’s worth asking for a quote if you see:
- Grout that stays dark however much it’s cleaned
- Floor grout that won’t come clean
- Gaps where the shower grout has gone
- Crumbling grout between the tiles
For landlords with property near Whitstable station, clean grout and fresh sealant between tenancies make a bathroom look cared for again.
What your quote should include
- What the quote includes, VAT included or not
- What the cure time is
- How the colour is chosen
- How the joint is cleaned and prepared
What else we do in Highstreet
DIY versus a professional finish
A careful DIYer can reseal a simple joint, like a short, easy-to-reach joint indoors. The common mistakes are sealing over old sealant, sealing a damp joint and using far too much.
Overfilling a joint is a classic DIY mistake. A thick, smeared bead looks untidy and does not move well, and getting the depth right matters as much as the look.