Essex · England
Bathroom & kitchen resealing in High Ongar, Essex
Baths, showers and worktops in High Ongar need attention? We cut out the old, prepare the joints and apply the right sealant.
- A reseal done over the top of the old bead
- Black spots spreading through the bead
- Gaps where the bath or tray has moved
How we handle bathroom resealing in High Ongar
A reseal only lasts if the joint is properly prepared. The old sealant is removed to the last smear, after which the joint is degreased and any mould treated. Only once it’s dry does the new bead go on. Common call-outs are for leaks into the floor or ceiling below and lumpy, uneven sealant from a DIY attempt, across kitchen worktops & upstands, sinks & splashbacks and basins & vanity units.
In a village or hamlet like High Ongar, homes are often older cottages and farmhouses alongside a few newer houses. Movement in older walls and floors tends to show first as cracked grout or split sealant.
All our work is covered by our 12-month guarantee.
- Place
- High Ongar (CM5)
- Wider area
- Essex
- Guarantee
- 12 months on all our work
- Quote
- A clear price before work begins
- Phone
- 0345 464 0079
- Page updated
- 26 October 2026
Signs you need bathroom resealing in High Ongar
Older sealant shrinks and hardens. Along worktops it tends to pull back from the wall, opening a hairline gap that lets water and crumbs in. Hot pans and harsh cleaners don’t help.
Signs it’s time to call us include:
- Water escaping at the shower enclosure
- A bead that has pulled away from the tiles
- Mouldy sealant that has gone black
- Two layers of silicone, both failing
Homes close to Church of St Mary the Virgin include some older properties, and timber floors under older bathrooms flex, so joints need a sealant that moves with them.
Before booking anyone
- Whether they’re fully insured
- The length of the guarantee
- What happens if the job turns out different
- What preparation is included
How it works
On the day, there’s very little for you to do. Point us to the joints and we will get on with it. The work itself takes half a day or less for one room, longer when the kitchen is included, including the tidy-up. Somewhere as small as High Ongar, access is often the only tricky part. For outside work, also let us know about exposed walls and any outbuildings involved.
- First, each joint is checked for movement and signs of water.
- Every trace of the old bead is removed, including the thin smear on the tiles.
- The joint is cleaned, degreased and treated for mould.
- With the joint dry, and any bath loaded with water, a single bead of anti-fungal silicone is applied.
- The bead is tooled smooth and you are told the cure time, usually around 24 hours.
Getting ready for the visit
- Tell us about any water getting in
- Mention if the joints have been sealed before
- Mention any sign-in or site rules at work premises
Get a quote
Getting a quote is simple: let us know the job and the location, and roughly how big it is. Photos by email help us understand the job.
Related advice
Places near High Ongar
Other services in High Ongar
What the job involves on each surface
Basins & vanity units
On a basin, neatness shows: the bead is right in front of you, so it’s tooled cleanly and evenly, finished in a colour that suits the basin.
Baths
A bath shifts slightly every time it’s filled, so it’s filled with water before the bead goes on. That way the joint is laid with the bath at its heaviest and isn’t torn the first time it’s used.
Why act early in High Ongar
You do not need a new bathroom because the sealant looks bad. A new bead often brings the whole room back, provided the bath, tray and tiles are in good order. If something else is wrong, we’ll tell you. Around High Ongar, older homes often have timber in their floors and frames, and water through a failed joint can rot timber if it’s left.
The cost depends on the amount of work, how much old material has to come out and access to the work. You’ll have a clear quote before any work starts.
Why High Ongar customers choose us
- A 12-month guarantee on all work
- We agree the colour with you first
- Experience in homes, commercial sites and hotels
- Sanitary silicone with an anti-fungal additive in wet areas
Read what affects the cost and what customers say.
Aftercare tips
Joint life depends on how it’s used and looked after. Here’s what we suggest:
- Wipe up water along the back of the worktop
- Never pick at the silicone with a blade
- Keep bottles off the sealant line
- Wait for the cure time we give you
In a kitchen, don’t let water sit along the back of the worktop and keep hot pans off the bead. The drier the joint stays, the longer it lasts.
A failed kitchen joint is easy to miss. Water gets behind the upstand and into the edge of a laminate worktop, where it can make the board swell. Resealing before that happens protects the worktop.
DIY versus a professional finish
Sealing over old silicone is the commonest DIY error. New silicone will not bond to old, so it peels away and traps moisture behind it. All the old material has to come out first.
If you’ve already had a go yourself, that’s fine. We cut it out and start again.
Bathroom resealing around High Ongar
Most of the South East has hard water, which leaves limescale on sealant, grout and fittings.
If you look after a building such as High Ongar Primary School, its toilets, changing areas and kitchens need their sealant renewed like any other building’s.
High Ongar is about 6 miles north of Brentwood, in Essex. Across the CM5 area, our applicators can take on bathroom resealing. We cover 644 towns and villages across Essex, large and small. You can also see our page for Chelmsford, about 10 miles away.
Work in CM5 is quoted and booked the same way as anywhere else. Local streets include The Street, Mill Lane and Millfield, all of which we cover. We also cover the places around High Ongar: Chipping Ongar (1 mile west), Shelley (1 mile north-west), Norton Mandeville (1 mile north-east), King Street (1 mile east) and Greensted (2 miles west). Further out, we also cover Chelmsford (10 miles east), Basildon (12 miles south-east), Harlow (8 miles north-west), Brentwood (6 miles south), Billericay (9 miles south-east) and Loughton (9 miles south-west).
Landmarks near High Ongar
Typical jobs here are in homes near Red Lion Public House and The Ongar Academy. Other landmarks nearby include Willingale Doe (3.7 miles north-east).
What affects the cost of bathroom resealing
For a quick quote, just ask. What matters most is:
- Which sealant suits the joint
- The size of the job
- Whether there’s mould to deal with
- Access and height
A few things move the cost up or down: how much old sealant there is and how stubborn it is, any mould to treat, and whether the work is at height. We take all of that into account in your quote.
What to tell us for a quote
To help us quote quickly, please include:
- Whether it has been sealed before
- Any access issues, like height or stairs
- Whether it’s a home or a business
- Roughly how big the job is
Need a quote? Please call 0345 464 0079 or email us with a few details. We’ll explain what we’d do and give you a clear price before work begins.
High Ongar: your questions answered
Do you cover High Ongar for bathroom resealing?
Yes. We work across London and the South East, and High Ongar is part of that. You can ring 0345 464 0079 or drop us an email and let us know what needs doing, and we will give you a clear quote.
What guarantee comes with bathroom resealing in High Ongar?
Every job comes with our one-year guarantee, wherever it is. We are fully insured, and an ARBOMaster approved applicator.
Can tenants book the work?
Of course. Check with your landlord; we can send the quote to them too.
Is white the only colour available?
Most people choose white or clear, but other colours can be used to suit tiles and worktops. Tell us what you’d like when you get in touch.
Do the sealants smell?
That depends on the sealant. Some smell for a while, some hardly at all.
Are you fully insured?
Yes, we’re fully insured for domestic and commercial work.
What do you put in the joint?
We choose the sealant for the joint, not the other way round. Where it moves, gets wet or faces the weather makes a difference, and we’ll tell you what we are using.
Should I try DIY first?
Sometimes. Preparation is everything: all the old sealant out, and a clean, dry joint. If it does not work out, we can redo it.